Line a room with wallpaper and you have instant decoration. From blah to bold within a matter of hours, newspaper roomgood.ru could push boundaries beyond what paint can do. It enlivens walls with textures or patterns or both--your choice. And as a bonus, it masks minor imperfections in plaster and drywall, too.
However, as frequently as homeowners try to hang themselves, they rarely get it right, cursing their peeling seams and mismatched patterns--it's enough to drive you up a wall. Input John Gregoras, a pro paper hanger from Somers, New York, with almost two decades' experience. We asked Gregoras to demonstrate some of his very best wallpapering tips and shortcuts for pasting, hanging, aligning, and trimming. And, boydid we learn a lot - everything from how he intends the layout to how he lines up the previous seam. With this type of insider know-how, papering only got a whole lot easier.
Best Wallpaper Techniques Overview
Design is the key if you are learning how to hang wallpaper. Paying attention to the sequence where the paper goes up ensures your pattern will remain well-matched and seem straight. John Gregoras recommends functioning in 1 direction around the space to keep the pattern consistent.
But regardless of how good your technique, the routine between the first and final strip will rarely match up. For that reason, Gregoras always begins his job behind a doorway, papering out from the corner till he reaches the distance above the door-- the least conspicuous place in the room.
Frequently, the final strip of paper onto a wall is not a complete sheet. Another wallpapering suggestion Gregoras uses is to constantly paper the corners together with broken sheets.
Click button at top right to expand case.
Apply Wallpaper Paste
Paint the entire room with a wall primer/sizer.
Unroll the wallpaper. As you do, check for flaws and haul the paper from the edge of your worktable to take away the curl.
Cut in the exact same place on the repeat so patterns on adjacent sheets will lineup.
Lay a cut sheet onto the table, face down.
Tip: Don't allow paste to have on the desk or it will mar the next sheet (wash it off with a barely damp sponge if it does). Slide the paper all the way to the border of this table to apply paste to the ends and borders.
Novel the Paper
Fold the glued back of this paper on it, top and bottom ends assembly in the middle. Make sure that the side borders line up perfectly. Smooth the paper onto itself as far as possible without creasing the folds.
Place the paper aside to permit the paste to soak in and the paper to relax. Be sure to follow the exact booking time advocated on the wallpaper's label, which differs depending on its material (more for vinyl-coated wallcoverings, less for uncoated papers).
Align First Strip
Start at a corner near a doorway. In case the doorway is far from the corner, draw a reference line parallel to the door near the corner.
Unfold the top of the booked paper and hang it on the wall. Overlap about 2 inches at the ceiling and 1/8 inch in the corner. Gently press it in place.
Unfold the bottom of the novel and let it hang. Examine the dimension between the newspaper and the door casing or benchmark line. Adjust the paper to help keep it parallel to the door but still overlapping at least ⅛ inch in the corner.
Tuck and Trim the Paper
When the sheet is aligned, use the edge of a newspaper simpler to tuck the paper to the corner at the ceiling. Then, working from the top down, sweep the smoother within the whole sheet. (Do not press so hard for you to push out glue.)
Trim the excess paper in the ceiling: Push a 6-inch taping knife into the joint between the ceiling and wall. With a razor, cut above the knife to trim off the excess. Work slowly. Alternate between moving and cutting the knife. Don't slide the knife and razor together. Continue papering to a point over the door.
On the adjoining wall, then draw a plumb line (if there's no door or window).
Hang a strip at the corner. Overlap the present bit on the adjoining wall by 1/8 inch. Measure to the plumb line and correct the paper to maintain the space equivalent. Smooth the newspaper. Trim at the ceiling and trim the corner.
Hang another strip of newspaper. Unfold the top of the novel and place it on the wall. Match the pattern as closely as you can, leaving just a hair's breadth between sheets.
Suggestion: Push out air bubbles by sweeping the newspaper simpler from the middle out to the edges. Wipe off glue on the surface with a sponge.
Close to the Seams
Lightly press on the surface of the paper into the wall. Then gently roll the seam with a seam roller to flatten down the edges.
Unfold the bottom of the sheet and then finish matching and shutting the seam. Then tightly roll down the whole seam, working a full 3 inches in from the border.
Smooth the whole sheet. Continue papering the room, trimming and overlapping corners as shown in Step 5.
Tip: If the booked end of the strip starts to dry out before you hang it, then wipe the wall with a damp sponge. This may remoisten the paste when you hang the paper.
Cut in Around Moldings
At doors and windows, let the paper float the molding by at least an inch.
Using the razor, make a relief cut from the paper. Carefully run the razor from the molding corner out to the border of this paper. Use the molding for a guide.
Press the cut edge tight in the joint between the molding and the wallsocket.
Smooth down the entire sheet.
Hide little cutting errors on darker papers by bleach the wall or the white edge of the paper with a mark that matches the paper. Some pros even color all of the paper's edges so seams are not as evident should the newspaper shrink as it dries.
Paper the cover plates of electrical fixtures to make them vanish. Cut a sheet of wallpaper larger than the plate. Cut out of the component of the pattern that matches the paper onto the wall around the switch.
Hold them on the wall and adjust the paper to match the pattern onto the wall.
Hold the paper and then flip the plate . Cut the corners off 1/8 inch off from the plate. Wrap the paper above the plate and then tape it on.
Cut out the switch or receptacle holes using a razor. Make Xs in the screw holes. Screw the plates back to the wall.